What is the correct command to copy the contents of the harddisk:/showtech folder to an FTP server? A. copy harddisk:/showtech location 0/RSP0/CPU0 ftp: B. copy harddisk:/showtech ftp: C. copy /recurse harddisk:/showtech location 0/RSP0/CPU0 ftp: D. copy /recurse harddisk:/showtech ftp: E.…

Referring to the diagram and configuration on Routers XR-1 and XR-2, which three statements are correct? (Choose three.) A. Router XR-1 can never be a designated router or designated intermediate system. B. The transmission of IS-IS packets will be suppressed…

Which two of the following are correct commands to activate the PIE file <hfr-mgbl-p.pie-4.0.1>? (Choose two.) A. install add tftp://172.20.165.36/hfr-mgbl-p.pie-4.0.1 activate B. install activate tftp://172.20.165.36/hfr-mgbl-p.pie-4.0.1 C. install add disk0:hfr-mgbl-p-4.0.1 activate D. install activate disk0:hfr-mgbl-p.pie-4.0.1

Which command will correctly deactivate asr9k-mpls-p-4.1.0? A. RP/0/RSP0/CPU0:P1 (admin)#install remove disk0:asr9k-mpls-p-4.1.0 B. RP/0/RSP0/CPU0:P1 (config)#install deactivate smu location disk0: C. RP/0/RSP0/CPU0:P1 (admin-config)#deactivate disk0:asr9k-mpls-p-4.1.0 D. RP/0/RSP0/CPU0:P1 (admin)#install deactivate disk0:asr9k-mpls-p-4.1.0 E. RP/0/RSP0/CPU0:P1 #asr9k-mpls-p-4.1.0 disk0:deactivate sync

Which answer best summarizes the difference between p and px images, hfr-mini-p.vm-4.1.1 and hfr-mini-px.vm-4.1.1, respectively? A. P images can only support legacy hardware, while px images can only support new CRS-3 hardware. B. P images can use an SMU to…

Which Cisco IOS XR command sequence will load a specific configuration? A. (config)#load disk0:name.cfg B. #copy disk0:name.cfg running-configuration C. #copy tftp://255.255.255.255/name.cfg D. #load commit changes <name> E. (config)#load commit <name>

Which of the following functions can be configured in the Administration Config mode? (Choose two) A. BGP routing B. MPLS Traffic Engineering C. SDR hostname D. Secure Shell login E. nonowner SDR

In order to determine the hardware and firmware revision of a linecard, what is the correct command that should be invoked? A. RP/0/RP0/CPU0:CRS-MC#show version B. RP/0/RP0/CPU0:CRS-MC#show platform C. RP/0/RP0/CPU0:CRS-MC(admin)#show platform D. RP/0/RP0/CPU0:CRS-MC#show diagnostic summary E. RP/0/RP0/CPU0:CRS-MC(admin)#show diag details

In which mode can you check the power usage of a chassis? A. in EXEC mode B. in admin mode C. in both EXEC and admin mode D. in ROMMON mode E. in environmental mode

Refer to the exhibit. If you have ROMMONs and FPDs with the Upg/Dng field marked "Yes" and you ran the upgrade hw-module fpd all location all command, what did you upgrade? A. upgraded only the FPD for the cards that…